- What your electrician needs to know before fitting downlights: Before your electrician fits downlights, send them the hole size, the depth each light needs, its fire, IP and insulation ratings, your layout and your dimmer. Ask whether the work is notifiable under Part P and which certificate you’ll get. Check the lights when they arrive, clear the room and keep the certificate safe.
- Integrated LED or GU10: which downlight should you choose?: An integrated LED downlight has its LEDs built in, so it can be slimmer and is often sealed, but the whole fitting is replaced when it fails. A GU10 downlight takes a mains bulb you can change yourself and needs more depth. Choose integrated for shallow ceilings, bathrooms and low glare, and GU10 for flexibility.
- Lumens, watts and beam angles: how bright should downlights be?: Judge brightness by lumens, the amount of light a downlight gives out. Watts only show the electricity it uses. As a rule of thumb, aim for 300–400 lumens per square metre in kitchens and 100–200 in living rooms and bedrooms. Use wider beams on standard ceilings, narrower beams on tall ones, and fit a dimmer.
- Low-glare downlights and UGR explained: Low-glare downlights set the LED deeper inside the fitting, often behind a baffle, so you see less of the bright source from across the room. Look for a low glare (UGR<19) rating. They matter most where you sit or lie and look up, and they usually need more depth above the ceiling.
- Replacing halogen downlights with LED: If your halogen downlights take GU10 bulbs, you can usually swap to LED GU10 bulbs as long as the fittings are in good condition. MR16 bulbs run at 12 V from a transformer, so a straight swap often flickers. Replacing the whole fitting lets you add fire rating and better sealing at the same time.
- Dimming LED downlights without flicker: When LED downlights flicker or buzz, the most common cause is a dimmer made for halogen bulbs. Use a trailing-edge dimmer that gives an LED load range, keep your total wattage inside it, and check the downlights are dimmable and listed as compatible. Smart downlights dim through an app and need a plain on/off switch.
- Fire-rated downlights explained: A fire-rated downlight helps a ceiling keep its fire resistance after you cut a hole in it, for 30, 60 or 90 min depending on the ceiling it was tested in. You usually need them where a ceiling separates floors, as in flats, loft conversions and houses of three or more storeys. Building control can confirm what yours needs.
- How many downlights do I need?: For a standard 2.4 m ceiling, space downlights about 1.2 m to 1.5 m apart and half that distance from the walls. Divide the room's length and width by the spacing to get the number in each direction. Then check the total lumens against the floor area, and add lamps or task lights where you need them.
- Kitchen downlights: layout, colour and glare: Put kitchen downlights roughly above the front edge of the worktop so you don't work in your own shadow, about 1 m to 1.2 m apart. Choose 3000 K for a warm kitchen that opens onto living space, or 4000 K for a crisp working feel. Look for CRI 90 for natural food colours and low glare for kitchen-diners.
- Bathroom downlights: zones and IP ratings explained: Bathrooms are divided into zones around the bath and shower. Downlights in Zone 1, above the bath or shower tray up to 2.25 m, and Zone 2, 0.6 m beyond it, need at least IPX4. Fit steam-proof (IP65) over a bath or shower. Every bathroom circuit needs RCD protection, and a qualified electrician should do the work.
- Choosing a colour temperature for downlights: Colour temperature describes how warm or cool light looks and is measured in kelvin (K). Warm white (3000 K) suits most homes, extra warm white (2700 K) suits bedrooms and living rooms, and cool white (4000 K) suits kitchens, bathrooms and work areas. Keep one setting per space and choose high colour rendering (CRI 90) where colour matters.
- How to measure for downlights: To measure for downlights, switch the lighting circuit off at the consumer unit, take out one fitting and measure straight across the hole in millimetres. Then measure from the ceiling surface up to the first obstruction above. Choose a fitting whose cut-out range includes your hole width and whose recess depth fits the space.
- The complete downlight buying guide: To choose a downlight, start with your ceiling. Measure the hole width and the depth above, then check whether you need a fire rating, an IP rating or an insulation-coverable fitting. After that, pick a type, a colour temperature and a brightness, and make sure it works with your dimmer. The finish is down to taste.
The Downlight Co. · All downlights · Guides · Help · Basket