Low-glare downlights set the LED deeper inside the fitting, often behind a baffle, so you see less of the bright source from across the room. Look for a low glare (UGR<19) rating. They matter most where you sit or lie and look up, and they usually need more depth above the ceiling.
Glare is the discomfort you feel when a small, very bright light sits in your view against a darker background. Your eyes try to adjust to the bright point, so everything around it looks dimmer and you find yourself squinting or looking away. Lighting designers call this discomfort glare. When it is strong enough to make detail harder to see, it’s called disability glare.
Glare depends on contrast as much as on how much light there is. A downlight that looks fine in a bright white kitchen at midday can feel harsh at night in a room with dark walls. The same light can also feel different depending on where you sit, because what matters is how much of the bright source reaches your eye.
Downlights are prone to glare because they concentrate a lot of light in a small patch of ceiling. An LED is a tiny, intense source. If you can see the LED, or a small clear lens in front of it, your eyes notice.
Many basic downlights put the LED, or a thin diffuser in front of it, almost level with the ceiling. From directly below that is fine. From across the room you still see the bright disc, because nothing blocks your view of it.
Most of the time you look across a room rather than straight up. When you sit on a sofa or at a dining table, a flush downlight a few metres away sits in the upper part of your view. Several in a grid become a row of bright spots, and the ceiling around them looks darker by comparison.
People describe the effect in different ways. Some find it tiring over an evening. Others notice a sparkle at the edge of their vision, or a spot that lingers after glancing at a light. Some people are more sensitive to glare than others, so if someone in your home finds the lighting harsh, glare is worth ruling out first.
Low-glare downlights move the light source up inside the fitting, away from the ceiling surface. The body of the fitting then shades the LED from the side. You only see the bright source when you are close to underneath it. From elsewhere in the room you see light on the floor and walls, and a softly lit opening in the ceiling.
[diagram:glare]
The deeper the source sits, the closer you have to be to directly below the light before you can see it. Lighting designers call the angle at which the source disappears from view the cut-off angle. Manufacturers use a few features to control it.
Opal diffusers work differently. They spread the light over a larger disc, which lowers the brightness of any single point, although the whole disc stays visible from across the room. Many people find an opal downlight softer than a clear lens. A deep-recessed fitting usually does more to hide the source.
UGR stands for unified glare rating. It is a number, usually between about 10 and 30, that estimates how much discomfort glare people will feel in a lit room. Lower numbers mean less glare. Our UGR glossary entry gives a short definition.
UGR comes from workplace lighting design. The European standard for lighting indoor workplaces, EN 12464-1, sets maximum UGR values for different tasks. For example, UGR 19 is the usual limit for office desk work, and higher limits are allowed in corridors and stores. There is no equivalent rule for homes, but the same scale is a useful way to compare lights.
| UGR value | How to read it at home |
|---|---|
| Below 16 | Very low glare. Suits rooms where you often look towards the ceiling. |
| 16 to 19 | Low glare. A good benchmark for living spaces and kitchen-diners. |
| 19 to 22 | Moderate. Usually fine in rooms you pass through or where you mostly look down. |
| Above 22 | Noticeable glare for many people, especially in the evening. |
These bands are a rough guide for homes and are not taken from any standard.
UGR is really a measure of a whole room design. The calculation takes in the room size, the number and position of the lights, how reflective the walls and ceiling are, and where the viewer sits. A single fitting doesn’t have one fixed UGR.
When a downlight is sold as low glare (UGR<19), the figure has usually been calculated for a standard reference room with set dimensions and surface finishes. That makes it a fair way to compare one fitting with another. Treat it as a good sign rather than a guarantee for your room. A dark ceiling, a low ceiling or lights placed right in your line of sight can all make glare worse than the figure suggests.
The beam angle describes how widely a downlight spreads its light. A narrow beam, such as 36°, sends most of the light down in a cone. A wide beam, 90° or more, throws light out to the sides as well.
Wide beams light a room evenly, but they also send more light towards your eyes when you look across the room. Narrower beams usually control stray light better, so they tend to feel less glaring. The trade-off is that you may need more fittings, placed closer together, to avoid dark patches between pools of light. Our guide to lumens, watts and beam angles explains how to balance the two.
Brightness plays a part too. A very bright fitting with a clear lens will feel harsher than a softer one of the same design. More lights at a lower output, or lights on a dimmer, usually feel more comfortable than a few very bright ones. If you plan to dim, make sure your dimmer suits LED lights. Our dimmer and flicker guide covers the checks.
Warmer colour temperatures, such as 2700 K or 3000 K, often feel gentler in the evening. They don’t change the UGR figure, which is based on brightness alone.
Low-glare fittings cost more, so use them where they make the biggest difference. As a rule, that is wherever people sit or lie still and look up or across the room.
In halls, utility rooms and walk-in wardrobes you mostly pass through or look down, so a standard fitting is usually fine. Stairs are the exception. Looking up a staircase at night can put the lights straight in your eyes.
Low-glare downlights are a sensible upgrade in the right rooms, but they come with a few compromises. Check these before you order.
| Consideration | Standard downlight | Low-glare downlight |
|---|---|---|
| Price | Lower | Usually higher, because of the extra optics and deeper body |
| Depth above the ceiling | Can be very slim | Usually needs more space above the ceiling |
| Light spread | Often wider | Often narrower and more controlled, so you may need more fittings |
| Look on the ceiling | Bright disc visible across the room | Softly lit opening until you are close to underneath |
| Light for each watt | Can be higher | Can be a little lower, as baffles absorb some light |
Depth is the one to check first. With the lighting circuit switched off at the consumer unit, measure the space above your ceiling to the first joist, pipe or layer of insulation, then compare it with the recess depth on the product page. Our guide on how to measure for downlights walks you through it.
Trimless fittings are worth a mention. They are plastered into the ceiling so no rim shows, and some pair that clean look with very low glare. They need a larger hole, more depth and a plasterer as well as an electrician, so they suit new ceilings and full renovations more than a straight swap. If a trimless fitting isn’t fire-rated and the ceiling needs to resist fire, it will need a fire hood above it.
Three lights cover most situations. Our deep-baffle downlight is the only light in our range with a published glare rating below 19 (UGR<19), in white or black. Our anti-glare CRI 90 downlight sets the LED deep behind the bezel, has CRI 90 for natural colours and is IP65 for bathrooms. Our indirect anti-glare downlight bounces the light and fills old 97 mm holes. All three are fire-rated to 90 min.
[products:ugr19-low-glare-fire-rated-ip65-downlight,anti-glare-fire-rated-ip65-downlight-cri90,indirect-anti-glare-fire-rated-ip65-downlight-97mm]
See every option in our low-glare collection, or answer a few questions and we’ll show what fits your ceiling depth, hole size and room.
For homes, UGR<19 is a sensible benchmark. It matches the limit commonly used for office desk work, where people look at screens and paper for hours. UGR<16 is very low and suits bedrooms or anywhere you often look up. A quoted UGR is usually calculated for a standard room, so use it to compare fittings rather than as a guarantee for your ceiling.
They can give the same light on the floor and worktops as a standard downlight. The difference is that less light heads sideways into your eyes, so the room feels calmer. Deep baffles do absorb a little light, so compare the lumen figures on the product pages. Our brightness guide explains how many lumens each room needs.
They’re worth it in a kitchen-diner, or anywhere with seating such as an island with stools. When you sit, you look across the ceiling, and bright spots over the island sit right in your view. In a galley kitchen where you mostly stand and look down at the worktop, a standard fitting is usually fine. See our kitchen lighting guide.
It means the manufacturer has calculated a unified glare rating below 19 for that fitting, usually in a standard reference room. Lower numbers mean less discomfort glare. The real figure depends on your room, the number of lights and where you sit, so treat it as a way to compare fittings and a sign that the light source is well shielded.
Usually because you can see the bright LED or lens from where you sit, often from flush, very bright fittings. Dark walls and ceilings make it worse. Dimming them, using lamps in the evening or swapping the worst ones for deep-recessed fittings usually helps. Browse our low-glare downlights to compare designs.
Yes, with two checks. A sloped ceiling points the fitting into the room, so you can end up looking into it. Deep-recessed fittings, or adjustable ones that tilt the beam back towards the floor, help. Loft rooms also often have little depth between the plasterboard and the roof, so measure first. Our adjustable downlights tilt to aim the light, some by 20°.
Usually, yes. Hiding the LED further up inside the fitting makes the body taller. Our anti-glare CRI 90 downlight needs 56 mm above the ceiling, compared with 35 mm for our ultra-slim downlight, and our deep-baffle UGR<19 downlight needs 75 mm. Measure up to the first joist, pipe or insulation with the lighting circuit switched off, and compare it with each product page. Our measuring guide shows how.
The Downlight Co. · All downlights · Guides · Help · Basket