Kitchen downlights: layout, colour and glare

Put kitchen downlights roughly above the front edge of the worktop so you don't work in your own shadow, about 1 m to 1.2 m apart. Choose 3000 K for a warm kitchen that opens onto living space, or 4000 K for a crisp working feel. Look for CRI 90 for natural food colours and low glare for kitchen-diners.

Key points

  • Line downlights up over the front edge of the worktop, clear of the wall units, to avoid shadows.
  • Space them about 1 m to 1.2 m apart along the run, and centre them on features such as the sink and hob.
  • 3000 K suits kitchens that open onto living areas. 4000 K gives a crisper feel. Keep one colour across the ceiling.
  • CRI 90 or above shows food colours more naturally.
  • Use low-glare fittings where people sit, such as dining areas and island seating.
  • Add under-cabinet lighting for the worktops, and use fire-rated downlights where there's a room above.

Where to put downlights over worktops

A grid of downlights in the middle of the ceiling is a common kitchen mistake. When you stand at the worktop, the light is behind you, and your head and shoulders cast a shadow on what you're doing.

Run a line of downlights roughly above the front edge of the worktop instead. On a standard 600 mm deep worktop, that puts them about 600 mm out from the wall, so light falls onto the worktop in front of you. If you have wall units, this position also keeps the lights clear of the unit fronts, so the tops of the cupboards don't cut off the beam.

Where there are no wall units, such as under a window or along open shelving, keep to the same line so the lights look consistent around the room.

Along the run, space the lights about 1 m to 1.2 m apart. Try to centre them on the things you'll look at, such as the sink, the hob and the middle of each run of worktop, and line them up with the cabinet doors where you can. A layout that follows the kitchen looks planned, even when the spacing varies a little.

Islands and pendants

An island is a worktop and, often, a place to sit. It needs good light on the surface without dazzling people on the stools.

Pendants are the usual choice. A common guide is to hang them so the bottom of each shade is about 750 mm to 900 mm above the island top. That lights the surface and keeps the view across the kitchen clear. Two or three pendants spread evenly along the island usually look balanced. Put them on their own switch or dimmer.

If you'd rather use downlights over an island, line them up over the working side, or run a single line down the middle of a narrow island. For a wide island with seating on one side, use two lines, one over each long edge. Choose low-glare fittings, which are more comfortable for anyone sitting nearby.

If the island has a hob, the extractor affects where lights can go. See the section on steam and extractors below.

How many kitchen downlights and how far apart

Kitchens need more light than most rooms. As a rough starting point, aim for about 300–400 lm per m² of floor from the ceiling lights, then add under-cabinet lighting for the worktops. Our guide to how many downlights you need explains how to work this out.

A typical layout has two parts.

  • A line of downlights over the worktops, about 1 m to 1.2 m apart.
  • General light for the middle of the room, spaced about 1.2 m to 1.5 m apart, or pendants over an island or table.

For example, a 4 m by 3 m galley kitchen with worktops along both long walls might have 4 downlights over each run, 8 in total. At about 500 lm each that is 4,000 lm over 12 m², or about 330 lm per m². In a galley that is enough on its own, as the two lines also light the floor between them. In a larger kitchen, add central lights on a separate switch, so you can use just the ones you need.

3000 K or 4000 K in a kitchen

Colour temperature, measured in kelvin (K), has a big effect on how a kitchen feels. Use the switch below to see the same kitchen at 2700 K, 3000 K and 4000 K.

3000 K warm white 4000 K cool white
How it feels Warm and relaxed, close to old halogen light Crisp, bright and neutral
Suits Kitchens that open onto dining or living areas, wood and warm colours Kitchens used mainly for cooking, white and grey handleless designs, utility rooms
In the evening Blends with lamps and living-room lighting Can feel stark next to warm lamps
Watch out for Bright whites can look slightly creamy Can feel clinical in a small or dark kitchen

If your kitchen opens onto a living or dining space, 3000 K is usually the safer choice, as the whole room then reads as one. Whatever you choose, use one colour temperature for all the downlights in the same space. Mixing 3000 K and 4000 K on one ceiling looks patchy. Colour-switchable (CCT) fittings let you decide on the day of installation. Our colour temperature guide covers the full range.

Colour rendering for food

The colour rendering index (CRI) measures how accurately a light shows colours, on a scale up to 100. Daylight and halogen bulbs score at or near 100. CRI 80 is common for LED lighting in homes, and it is fine for most rooms.

In a kitchen, a higher score is worth having. At CRI 90 or above, food looks closer to how it does in daylight. Colours look more natural, and it's easier to judge whether meat is cooked or fruit is ripe. Some products also quote R9, a separate score for strong reds. A higher R9 helps meat, tomatoes and berries look true to life.

CRI matters most for the lights over the worktops and the island, where you prepare food. It's worth checking for under-cabinet strips too.

Low glare in open-plan kitchen-diners

In a kitchen you mostly look down at the worktop. In a kitchen-diner or family room you also sit at a table or on a sofa and look across the room towards the ceiling. From there, a row of bright, flush LEDs can be uncomfortable, especially in the evening.

Low-glare downlights set the light source deeper into the fitting, so you see less of it from an angle. Look for low glare (UGR<19) in the product details. UGR, the Unified Glare Rating, is used in lighting design standards such as EN 12464-1. A lower number means less glare, and 19 is the limit commonly used for offices and similar work areas.

Use low-glare fittings over the dining table and anywhere people sit, and ideally throughout the space so the ceiling looks consistent. Put the dining area on its own switch and dimmer, so you can turn the kitchen lights down while you eat. Our guide to low-glare downlights explains more.

Under-cabinet and plinth lighting

Downlights light the room. Under-cabinet lighting sits close to the worktop with nothing between the light and your chopping board, so it puts light exactly where you work.

Layer What it does Tips
Downlights over worktops General light for the working areas Above the front edge of the worktop
Under-cabinet lights Direct light on the worktop Towards the front of the cabinet underside, with a diffuser
Pendants Light and focus over an island or table On their own switch and dimmer
Dining downlights Softer light over the table Low glare, on their own dimmer
Plinth lights Low-level glow and a night light For effect only; use products made for plinths

For under-cabinet lighting, a continuous LED strip in a profile with a diffuser gives even light. Fit it towards the front of the cabinet underside so it lights the whole worktop and stays out of sight. A diffused strip also avoids a row of bright dots reflecting in gloss or stone worktops. Match its colour temperature to the downlights.

Plinth lighting sits in the kickboards under the base units. It adds little light for cooking. It makes a gentle night light and gives the units a floating look. Floors near sinks and dishwashers get wet and mopped, so choose products designed for plinth use. Both types usually run from a driver, and connecting it to the mains is a job for your electrician.

Fire rating, steam and the extractor

Cooking is a common cause of house fires. If there's a bedroom or any other room above your kitchen, the ceiling is part of what slows a fire spreading upstairs. Use fire-rated downlights, or fire hoods over fittings that aren't fire-rated, so the holes don't weaken it. In flats, houses of three or more storeys and loft conversions this is often required, and elsewhere it's a sensible default. Our fire-rated downlights guide explains the ratings, and building control can confirm what your ceiling needs.

Steam and grease rise from the hob and collect on nearby fittings. Kitchens have no zones like a bathroom's. Even so, a sealed fitting is worth having near the hob and sink. A splash-resistant (IP44) or steam-proof (IP65) fitting keeps moisture and grease out of the body and is easier to wipe clean.

Extractors affect the layout too.

  • Avoid putting a downlight directly above the hob, where it takes the most heat, steam and grease.
  • A chimney or canopy hood usually has its own lights, so you don't need a downlight above it.
  • With a ceiling extractor or an island hood, keep downlights clear of it and follow the extractor maker's guidance on spacing.
  • Extractor ducting often runs through the ceiling void. Find its route before you mark out any holes.

Downlights that suit kitchens

Our anti-glare downlight has CRI 90 and a deep-set light source, and switches between 3000, 4000, 5000 and 6500 K, which suits worktops and kitchen-diners. Our magnetic-bezel downlight is steam-proof, switches between 2700 and 6000 K and comes in six finishes. Our indirect anti-glare downlight gives soft light and fills old 97 mm holes.

Questions

Where should downlights go in a kitchen?

Line them up roughly above the front edge of the worktop, about 600 mm out from the wall on a standard worktop, so the light falls in front of you. Space them about 1 m to 1.2 m apart and centre them on the sink, the hob and each run of units. Add general lights or pendants for the middle of the room.

How many downlights do I need in a kitchen?

As a rough guide, aim for about 300–400 lm per m² from the ceiling lights. A 4 m by 3 m kitchen typically needs 6 to 8 downlights at around 500 lm each, plus under-cabinet lighting. Use our how many downlights guide and its calculator to work out your own layout.

Is 3000 K or 4000 K better for a kitchen?

Both work. 3000 K warm white suits kitchens that open onto dining or living areas and feels more relaxed in the evening. 4000 K cool white gives a crisp, bright feel that suits kitchens used mainly for cooking. Pick one and use it across the whole ceiling. Colour-switchable fittings let you decide on the day.

Should kitchen downlights be fire-rated?

If there's a room above, fire-rated downlights or fire hoods are the sensible choice, as the ceiling helps slow a fire spreading upstairs. In flats, houses of three or more storeys and loft conversions they are often required. Check with building control if you're unsure. See fire-rated in our glossary.

Do kitchen downlights need to be IP rated?

Kitchens don't have zones like those in a bathroom, so no particular IP rating is required. A splash-resistant (IP44) or steam-proof (IP65) fitting is still a good idea near the hob and sink. It keeps steam and grease out of the fitting and is easier to wipe clean.

How high should pendants be above a kitchen island?

A common guide is about 750 mm to 900 mm from the island top to the bottom of the shade. That lights the surface and keeps the view across the room clear. Taller households and larger shades may suit the higher end. Put the pendants on their own dimmer so they work for both cooking and eating.

What CRI is best for kitchen lighting?

Look for CRI 90 or above for the lights over worktops and islands. Food looks closer to how it does in daylight, which helps when you're checking whether meat is cooked or fruit is ripe. CRI 80 is common and fine elsewhere in the home. See CRI in our glossary.

Can I put downlights above my hob?

Avoid putting one directly above the hob, where it takes the most heat, steam and grease. A canopy or chimney extractor usually has its own lights. Keep downlights clear of ceiling or island extractors, following the extractor maker's guidance, and use a sealed fitting nearby. Check where the ducting runs before you plan any holes.

The Downlight Co. · All downlights · Guides · Help · Basket